The fuel level indicator indicates the level of fuel in the fuel tank.
The display bars of the fuel meter fades towards the empty (E) when the fuel level decreases from full tank level (F).
The last bar of the fuel level indication in the instrument cluster will blink continuously when the fuel is less than 3 litre / 0.8 Imperial gallon / 3.17 quart.
Please do not ride the motorcycle with the low fuel indication blinking continuously as it may not only result in the motorcycle running out of fuel, but will also cause serious damage to the fuel pump. Please refuel as soon as the low fuel indication starts blinking.
Share link
ANTI-LOCK BRAKING SYSTEM (ABS)
Anti-Lock Braking System (ABS) will help prevent the brakes from locking the wheels, during sudden application of the brakes at high speeds or at low friction surfaces. This will help the rider to have better traction and control over the motorcycle and prevent the motorcycle from skidding which can cause an accident.
In the event of a sudden and hard application of the brakes by the rider, the sensors in the braking system will signal the ABS modulator to momentarily and continuously reduce the hydraulic pressure and thereby prevent the brakes from locking the wheels while reducing the speed of the vehicle. This will help the rider to control the motorcycle.
An ABS indicator lamp is provided in the cluster to warn the rider in the event of any malfunction of the ABS.
When the ignition and engine kill switch are switched in 'ON' position the ABS sign will glow and remain 'ON' till the motorcycle attains a speed of 5 kmph / 3 Mph and turns 'OFF'. This indicates the ABS is functioning properly. If the ABS indicator lamp does not switch 'OFF' and remains continuously 'ON' at higher speeds, it is recommended not to drive the ABS motorcycle. Get the brake system inspected and corrected through a nearest Authorised Royal Enfield Service Centre. Failure to do so can result in a serious injuries and loss of life.
Share link
WARNING
DO’S
While starting the engine do check the ABS indicator comes 'ON' and switches 'OFF when the vehicle speed exceeds 5 kmph (3.1 mph).
Please check the brake fluid at 'MAX' level in the front and rear brake master cylinders and there is no leak in the brakes systems.
Apply both the brakes simultaneously for better efficiency while braking.
In the event of the ABS indicator remaining continuously 'ON' please take the motorcycle to a nearest authorized Royal Enfield service station to inspectthe brakes system control of the vehicle.
DONT'S
Do not apply only the front or rear brakes it can lead to inef- ficient braking.
Do not release the brake lever/ pedal when pulsations are felt during hard application of the brakes in an emergency situation. The pulsations only indicate that the ABS is activated.
CAUTION
ABS is a safety feature to help prevent locking of wheels during sudden application of brakes. It is by no means a substitute for good riding practices and anticipatory braking.
Please ride carefully and apply brakes cautiously especially while cornering. ABS cannot estimate the 'weight shifts' and momentum of the motorcycle while negotiating a corner and therefore prevent skidding due to loss of traction.
Please anticipate the stopping distance required for the speed of travel and apply brakes well in advance so as to bring the motorcycle to a safe stop.
Please apply both brakes to stop- front brake momentarily earlier followed by rear brake. To have better traction and control of the motorcycle.
Always ensure that you ride well within the legal speed limits.
Failure to adhere to the above can cause an accident resulting in serious injuries and loss of life.
The control function causes a slight pulsing of the hand and foot brake levers.
NEUTRAL INDICATOR
This indicator glows when the vehicle is in neutral position.
Share link
MALFUNCTIONING INDICATOR LAMP
A Malfunctioning Indicator Lamp (MIL) is provided in the tachometer.
When both the ignition and engine kill switch is in 'ON' position and after vehicle is started, the MIL will glow for few seconds and switch 'ON' this indicates that all the functions of Electronic Fuel Injection (EFI) system is functioning normally. In the event of any malfunction in the EFI system MIL will glow continuously. It is recommended to take the motorcycle to a nearest Royal Enfield Authorised Service Centre for a detailed inspection and correction of EFI system.
Share link
ROLL OVER SENSOR
In the event of motorcycle falling over on either of its sides with the engine running and the gears engaged the roll over sensor will 'disable' both the ignition and fuel systems and switch 'OFF' the engine. This is to prevent any damage to the motorcycle and its rider. To reset the Roll over sensor and reactivate the ignition and fuel systems.
Ensure the motorcycle is made upright and is on its center stand.
Ensure gears are in correct neutral and the neutral lamp is glowing in the instrument console.
Switch 'OFF' both ignition & stop switches, wait for a few seconds and switch 'ON' the ignition and stop switch again, to start the engine.
Share link
WARNING
CAUTION